Several methods to prevent PCB printed board from warping
1. Why the circuit board is required to be very flat
On the automatic insertion line, if the printed board is not flat, it will cause inaccurate positioning, components cannot be inserted into the holes and surface mount pads of the board, and even the automatic insertion machine may be damaged. The board with the components is bent after welding, and the component feet are difficult to cut neatly. The board cannot be installed on the chassis or the socket inside the machine, so it is also very annoying for the assembly plant to encounter the board warping. At present, printed boards have entered the era of surface mounting and chip mounting, and assembly plants must have stricter and stricter requirements for board warping.
2. Standards and test methods for warpage
According to the US IPC-6012 (1996 edition) <<Identification and Performance Specification for Rigid Printed Boards>>, the maximum allowable warpage and distortion for surface-mounted printed boards is 0.75%, and 1.5% for other boards. This has improved the requirements for surface-mounted printed boards than IPC-RB-276 (1992 edition). At present, the warpage allowed by various electronic assembly plants, regardless of double-sided or multi-layer, 1.6mm thickness, is usually 0.70-0.75%. For many SMT and BGA boards, the requirement is 0.5%. Some electronic factories are urging to increase the standard of warpage to 0.3%, and the method of testing warpage complies with GB4677.5-84 or IPC-TM-650.2.4.22B. Put the printed board on the verified platform, insert the test pin into the place where the degree of warpage is the greatest, and divide the diameter of the test pin by the length of the curved edge of the printed board to calculate the warpage of the printed board. The curvature is gone.
3. Anti-board warping during the manufacturing process
1. Engineering design: Matters needing attention when designing printed boards:
A. The arrangement of interlayer prepregs should be symmetrical, for example, for six-layer boards, the thickness between 1-2 and 5-6 layers and the number of prepregs should be the same, otherwise it is easy to warp after lamination.
B. Multilayer core board and prepreg should use the same supplier’s products.
C. The area of
2. Baking board before blanking:
The purpose of baking the board before cutting the copper clad laminate (150 degrees Celsius, time 8±2 hours) is to remove the moisture in the board, and at the same time make the resin in the board completely solidify, and further eliminate the remaining stress in the board, which is helpful to prevent the board from warping. Helping. At present, many double-sided and multi-layer boards still adhere to the step of baking before or after the blanking. However, there are exceptions for some plate factories. The current PCB drying time regulations of various PCB factories are also inconsistent, ranging from 4 to 10 hours. It is recommended to decide according to the grade of the printed board produced and the customer’s requirements for warpage. Bake after cutting into a jigsaw or blanking after the whole block is baked. Both methods are feasible. It is recommended to bake the board after cutting. The inner board should also be baked.
Patch processing
3. The latitude and longitude of the prepreg:
After the prepreg is laminated, the warp and weft shrinkage rates are different, and the warp and weft directions must be distinguished during blanking and lamination. Otherwise, it is easy to cause the finished board to warp after lamination, and it is difficult to correct it even if the pressure is applied to the baking board. Many reasons for the warpage of the multilayer board are that the warp and weft directions of the prepregs are not distinguished during lamination, and they are stacked randomly.
How to distinguish the latitude and longitude? The rolling direction of the rolled prepreg is the warp direction, and the width direction is the weft direction; for the copper foil board, the long side is the weft direction, and the short side is the warp direction. If you are not sure, please check with the manufacturer or supplier.
4. Stress relief after lamination:
The multilayer board is taken out after hot pressing and cold pressing, cut or milled off the burrs, and then placed flat in an oven at 150 degrees Celsius for 4 hours, so that the stress in the board is gradually released and the resin is completely cured. This step cannot be omitted.
5. The thin plate needs to be straightened during electroplating:
When the 0.4～0.6mm ultra-thin multilayer board is used for surface electroplating and pattern electroplating, special clamping rollers should be made. After the thin plate is clamped on the flybus on the automatic electroplating line, a round stick is used to clamp the entire flybus. The rollers are strung together to straighten all the plates on the rollers so that the plates after plating will not be deformed. Without this measure, after electroplating a copper layer of 20 to 30 microns, the sheet will bend and it is difficult to remedy it.
6. Cooling of the board after hot air leveling:
When the printed board is leveled by hot air, it is impacted by the high temperature of the solder bath (about 250 degrees Celsius). After taking it out, it should be placed on a flat marble or steel plate to cool naturally, and then sent to a post-processing machine for cleaning. This is good for preventing warpage of the board. In some factories, in order to enhance the brightness of the lead-tin surface, the boards are put into cold water immediately after the hot air is leveled, and then taken out after a few seconds for post-processing. This kind of hot and cold impact may cause warping on some types of boards. Twisted, layered or blistered. In addition, an air flotation bed can be installed on the equipment for cooling.
7. Treatment of warped board:
In an orderly managed factory, the printed board will be 100% flatness checked during the final inspection. All unqualified boards will be picked out, put in an oven, baked at 150 degrees Celsius under heavy pressure for 3-6 hours, and cooled naturally under heavy pressure. Then relieve the pressure to take out the board, and check the flatness, so that part of the board can be saved, and some boards need to be bake and pressed two to three times before they can be leveled. Shanghai Huabao’s pneumatic board warping and straightening machine has been used by Shanghai Bell to have a very good effect in remedying the warpage of the circuit board. If the above-mentioned anti-warping process measures are not implemented, some of the boards will be useless and can only be scrapped.